Insulation Company in Burbank, CA
Blown in insulation solves the two problems Burbank homeowners complain about most: attics that turn into ovens by 10 a.m. and street noise that bleeds through walls in older bungalows. Most homes here were built between 1920 and 1965, and many still have thin, settled, or missing attic insulation. We install loose-fill cellulose and fiberglass, dense-pack walls, and spray foam for air sealing in Burbank homes every week. Call (866) 271-1602 for a free estimate and a straight answer on what your house actually needs.
Why Burbank Homes Are Different
Burbank sits in the east San Fernando Valley, where summer highs routinely exceed 100°F and attic temperatures can climb past 150°F by early afternoon. Winter nights dip into the 40s, so houses here see big day-night temperature swings that punish under-insulated attics and walls. The housing stock compounds the problem. The Magnolia Park and Rancho districts are full of 1920s to 1940s California bungalows and Spanish stucco homes, many with little or no attic insulation and wall cavities never designed for modern energy loads. The hills and airport-adjacent neighborhoods add 1950s and 60s ranch tracts with low-pitch roofs that make venting and blow-in access trickier than a standard suburban attic.
And then there’s the airport. Thousands of Burbank homes sit directly under Burbank Hollywood Airport departure and approach paths, plus film studio flight traffic. Sound attenuation is as big a driver here as thermal performance, which is why we regularly spec dense-pack cellulose and mineral wool assemblies alongside attic work. A home in Burbank isn’t just fighting heat; it’s fighting noise, and the right insulation strategy addresses both at once. Wildfire-season air quality adds another layer: a well-sealed thermal boundary keeps smoke and ash from pulling through attic gaps and wall penetrations.
Our Main Burbank Services
Most Burbank homeowners call us about one of two projects: re-insulating an underperforming attic or air-sealing a house with spray foam. Both are handled in-house by the same crew, with material choice driven by your home’s construction and your comfort goals rather than what we happen to have in the truck.
Attic Insulation in Burbank
Burbank attics bake. On a 105°F day, an uninsulated or thinly insulated attic can hit 150°F, and that heat radiates into the rooms below for hours after sunset. We remove settled or rodent-damaged material, air-seal the attic floor penetrations, and install loose-fill or batt insulation to the R-value your roof pitch and venting can support. Low-pitch ranch roofs in the airport neighborhoods often need a different approach than the gabled bungalows near Magnolia Park. For the full breakdown, see our Attic Insulation in Burbank page.
Spray Foam Insulation in Burbank
Spray foam is the right call when you need air sealing and insulation in one step, which matters in Burbank’s wildfire-smoke months and for homes under flight paths where gap sealing blocks both drafts and noise. We install open-cell foam for interior sound control and closed-cell foam where moisture or space is a concern. The material bonds to the structure and eliminates the tiny air leaks that fiberglass alone can’t touch. Full details on Spray Foam Insulation in Burbank, including where foam earns its cost versus other materials.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Blown In Insulation in Burbank
Blown in insulation is the most common retrofit we do in Burbank because it’s the fastest way to bring an old attic up to modern energy code without tearing out ceilings or walls. Loose-fill fiberglass or cellulose is pneumatically blown into attic floors and wall cavities, filling the irregular gaps and tight corners that batts leave exposed. In Burbank’s pre-war bungalows and 1950s ranch homes, where attic access is often cramped and old wiring or knob-and-tube remnants complicate the work, blown material conforms around obstacles without disturbing them. That matters in neighborhoods across 91505 and 91506, where original construction details are worth preserving. If you’re weighing materials, our Blown In Insulation hub page covers the full comparison.
Cellulose Insulation
Signs you need it
Your attic insulation has settled to below the top of the ceiling joists, or your upstairs rooms heat up faster than the rest of the house on summer afternoons.
What it costs in Burbank
Loose-fill cellulose for a typical Burbank attic runs $1.10 to $2.20 per square foot installed, depending on existing material removal and target R-value.
How we do it
We remove any compromised old material, air-seal the attic floor, and blow dense-pack or loose-fill cellulose to your target depth, finishing with a level check across all bays.
Blown In Attic Insulation
Signs you need it
Rooms below the attic won’t hold temperature, you can see bare drywall or joist tops from the attic access, or your cooling bills in July and August keep climbing year over year.
What it costs in Burbank
Blown in attic insulation in Burbank typically runs $1.00 to $2.30 per square foot installed, with the final number set by attic size, access difficulty, and the R-value your roof assembly can handle.
How we do it
We verify venting and baffle placement first, then blow loose-fill fiberglass or cellulose to the specified depth, raking it level around the perimeter and over any recessed light housings.
Blown In Fiberglass Insulation
Signs you need it
Your existing fiberglass batts are torn, compressed, or moisture-stained, and you want a material that won’t settle as much as cellulose over time.
What it costs in Burbank
Blown in fiberglass in Burbank runs $0.90 to $2.00 per square foot installed, often the lower-cost option when the attic is clean and dry and no old material needs hauling out.
How we do it
We blow the fiberglass in lifts to the calculated depth, check density with a ruler in multiple spots, and confirm the coverage meets your R-value target before we call the job done.
Loose Fill Insulation
Signs you need it
You’re adding insulation to an attic with irregular joist spacing, shallow cavities, or lots of obstructions that make batt installation impractical.
What it costs in Burbank
Loose fill insulation in Burbank ranges from $1.00 to $2.20 per square foot installed depending on material type and whether we’re topping off existing insulation or starting from bare drywall.
How we do it
We snake the blower hose into the attic from the exterior access, blowing material in a controlled pattern until the coverage is uniform and the target depth is reached.
What Blown In Insulation Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Blown in attic insulation (labor + material) | $1.00 – $2.30 per sq ft |
| Blown in fiberglass insulation | $0.90 – $2.00 per sq ft |
| Loose-fill cellulose (dense-pack walls or attic) | $1.10 – $2.20 per sq ft |
Will blown in insulation make my Burbank house quieter?
Yes, especially dense-pack cellulose in walls and attics. It adds mass that dampens sound transfer, which helps in Burbank neighborhoods under the airport flight path. Call (866) 271-1602 for an honest assessment of what your walls can accept.
How long does blown in insulation take in Burbank?
Most Burbank attics take one day, including setup, blowing, and cleanup. Dense-pack wall retrofits can run two days depending on access to the wall cavities from inside or outside. We’ll give you a firm timeline on the estimate.
Brands We Service in Burbank
We install insulation from brands that earn their place in the truck. That includes CertainTeed and Knauf fiberglass for standard attic blow-ins, Rockwool mineral wool where fire resistance and sound dampening matter, and Icynene and Demilec spray foam for air-sealing work. Most attic materials are stocked locally and ready for a same-week start. See our brands for the full breakdown.
Pricing for Insulation Company in Burbank, CA
| Service | Typical range in Burbank |
|---|---|
| Blown in attic insulation | $1.00 – $2.30 per sq ft |
| Blown in fiberglass insulation | $0.90 – $2.00 per sq ft |
| Loose-fill cellulose (attic) | $1.10 – $2.20 per sq ft |
| Dense-pack cellulose (walls) | $1.20 – $2.20 per sq ft |
| Spray foam insulation (open-cell) | $1.10 – $2.40 per board ft |
| Spray foam insulation (closed-cell) | $1.80 – $3.20 per board ft |
| Air sealing package | $400 – $1,100 per home |
Prices in Burbank push toward the top of these ranges when attics have low clearance, old material needs removal, or the roof pitch makes venting work slow. Every quote is upfront and line-itemed before we start, so the number on the estimate is the number you pay.
Neighborhoods We Serve in Burbank
We work across the full 91505, 91506, 91507, and 91508 ZIP codes, from the tree-lined bungalow streets of Magnolia Park to the hillside ranches near Stough Canyon and the airport-adjacent tracts off Hollywood Way. Attic crews in Burbank start early to stay ahead of the valley heat, so morning arrival windows are standard.
- Magnolia Park
- Rancho District
- Burbank Hills
- Airport District
- Stough Canyon
Service Area – Cities Near Burbank
Fontana Insulation covers Burbank and the surrounding communities across the east San Fernando Valley and northeast Los Angeles. For neighbors just over the city line, we also serve Glendale, CA, North Hollywood, CA, Universal City, CA, and Studio City, CA, with the same material-agnostic approach to insulation selection.
Serving Burbank, CA — Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Insulation Company in Burbank
Most attic insulation retrofits in Burbank don’t require a city permit, but wall cavity work and some spray foam applications may trigger a check depending on scope and building age. We’ll tell you on the estimate whether your project crosses that line.
We schedule Burbank jobs every weekday, with morning arrival windows standard so attic work happens before the valley heat peaks. Same-week starts are common for blown in attic work; wall retrofits and spray foam may take a few days to slot in.
Yes. A 1930s stucco bungalow with plaster walls and a gabled attic calls for a different approach than a 1960s ranch with a low-pitch roof and vented eaves. We match material and method to the house as it was built, not a generic template.
Ready to talk specifics about your Burbank home? Call (866) 271-1602 for a free estimate. We’ll walk the attic with you, point out what’s working and what isn’t, and give you a straight answer on material options and cost.
What happens when you call
- 1A real person answersNo phone trees — talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 1-hour.
- 4You approve before work beginsNothing starts until you say go.
What Burbank Customers Say
"Found and sealed a gap around the chimney chase that was basically an open chimney to the attic."
— Nadia Aziz"Installed baffles at the soffits so the new insulation didn't block the ventilation, which the previous contractor apparently never considered."
— Michelle Bennett"Attic was at maybe R-11 from the 1970s and blown in over the top would have just buried the problem. They removed the old material, air sealed the top plates and penetrations first, then blew in to R-49. The upstairs is a completely different house in August."
— Sarah Fletcher